Product Experts Available 1-888-787-3626

Filter Your Results

 

1971 PORSCHE 914 6 PORSCHE ENGINE COMPARTMENT

Search Term: 'All Parts'
Category: 'Engine Compartment'
Vehicle: '1971 PORSCHE 914 6'

26 Item(s) Sort by: Show: per page Grid  |  List
Best Sellers
O-Ring, Engine Case Stud, For 911®, 914-6 Porsche®, 1965 -1989 Part # P910317
Stock OE Replacement 24 Required Per Car Make sure you have all the hardware you need when you are ready to assembly your Porsche. Note: The Lock Tabs are used to secure the oil pump (2 per car), and the intermediate shaft gear (6 per car). Learn More
$0.99 ea.
Timesert Thread Repair Kits & Inserts, 8mm Timesert Insert , For Porsche® Part # P910354
TIME-SERT is a solid bushing insert. This guarantees easy installation and allows for full load use of tapped hole, ensuring protection against stress and vibration. TIME-SERT is thin walled due to synchronized internal external threads. Thin cross sectional area allows for installation in areas of limited space and clearance material. TIME-SERT Positive Placement. Having a flange on the top of the insert will insure that the insert will have positive placement and cannot wind down into the newly repaired hole. TIME-SERT is self locking. On installation the bottom internal threads of the insert are cold rolled to expand the mating external threads into the base material locking the insert in place. Locking mechanism is at the bottom of insert Learn More

Was: $2.99 ea.

Now: $1.99 ea.
Weltmeister® Bell Crank Bushings, For Porsche®, 1965 -1989 Part # P910242
Carburetors not holding a steady idle or staying adjusted? These problems are often caused by worn, sloppy bushings at the intake manifold bell crank. Weltmeister has cured this with oil impregnated, self-lubricating bushings for smoother, more positive action (original bushings plastic). Note: Same bushings used for throttle lever by tension spring on fuel injected vehicles and at lever behind gas pedal. * 912, 912E, & 914 Models Only Use These Bushings On The Gas Pedal Bell Crank. Learn More

Was: $5.98 ea.

Now: $4.99 ea.
Cylinder Head Washer, For 911®,930, 912, 914, Porsche®,1965-1977 Part # P901534
Genuine Porsche Part For Aftermarket Replacement See Part Number 65-10697 Don't spend thousands of dollars rebuilding your 911® engine just to have a leak develop because a washer is too thin or a barrel nut bottoms out before being torqued correctly. Replacing used hardware is cheap insurance Learn More
$7.99 ea.
Engine Hardware, (E) Lock Tabs, For Porsche®, 1965 -1989 Part # P910320
8 Required Per Car Make sure you have all the hardware you need when you are ready to assembly your Porsche. Note: The Lock Tabs are used to secure the oil pump (2 per car), and the intermediate shaft gear (6 per car). Learn More

Was: $4.99 ea.

Now: $3.99 ea.
Oil Seal, Main Shaft Transmission Seal, For Porsche®, 1955 -1976 Part # P904131
Installation of flywheel and from pulley seals are made easier with Oil Seal Installers found in the Tool Secton. Tech Tip: Never install a seal dry; add a thin film of oil on lip. Learn More
$2.99 ea.
Seal, Rear Main Crankshaft, For 911®, 930, 914-6, Porsche®, 1965 -1989 Part # P904148
Installs On The Flywheel Side Installation of flywheel and from pulley seals are made easier with Oil Seal Installers found in the Tool Secton. Tech Tip: Never install a seal dry; add a thin film of oil on lip. Learn More

Was: $8.99 ea.

Now: $6.99 ea.
Seal, Differential Output, For 914, 911® Porsche®, 1970 -1986 Part # P904145
45 x 68 x 10 2 Required Per Car Installation of flywheel and from pulley seals are made easier with Oil Seal Installers found in the Tool Secton. Tech Tip: Never install a seal dry; add a thin film of oil on lip. Learn More
$5.99 ea.
Wurth Metric Hardware Kit, General Bolt/Nut Assortment, 490Pieces, For Porsche® Part # P904302
A Must For Any Do-It-Yourself Its here. The ideal assortment of Factory-style metric hardware for working on your car. While this kit doesnt have every single bolt and nut, it does have many sizes unique to the kind youll never find at the local auto parts store. Select the bodywork hardware assortment or the general nut/bolt/washer assortment. Comes in a sturdy metal box. Learn More
$119.99 Kit
Oil Seal, Front Pulley Crankshaft Seal, For Porsche®, 1965 -1989 Part # P904136
Installation of flywheel and from pulley seals are made easier with Oil Seal Installers found in the Tool Secton. Tech Tip: Never install a seal dry; add a thin film of oil on lip. Learn More
$9.99 ea.
Porsche Engine Case Washer, Chamfered, 911/912/914, 1965-1989 Part # 65-10734
High Quality Replacement Costs Less Than Buying From The Dealer 24 Required Per Engine Attaches To Crankcase Main Through Bolts Fits Porsche 911/912/914 Need new engine case washers? These high quality replacements are made to fit and function just like the factory originals to provide years of reliable performance for your Porsche. You can always rely on Eckler's Automotion to keep your Porsche on the road for many years to come. Learn More
$3.49 ea.
Ultimate Engine Sound Pad, For 914 Porsche®, 1970 -1976 Part # P915461
Superior Noise Reduction  OEM Factory Appearance High-Tech Design Cut down the noise and heat coming from your engine compartment with this precision die cut firewall pad. It looks like a factory replacement part, yet superior materials and construction actually improve firewall insulation. Sound deadening felt with a reinforced foil backing reduces engine noise in the cabin, while a non-porous dense foam skin prevents heat transfer. Replace your deteriorated factory pad and improve cabin comfort simultaneously with the Ultimate Engine Pad. Learn More
$144.99 ea.
Engine Gaskets, Complete, For Porsche®, 1965 -1972 Part # P914178
Engine gasket sets from original equipment manufacturers such as Reinz and Ehlring. Learn More
$269.99 ea.
Timesert Thread Repair Kits & Inserts, 8mm Timesert Insert, For Porsche® Part # P910355
7 Piece Set   TIME-SERT® is a solid bushing insert. This guarantees easy installation and allows for full load use of tapped hole, ensuring protection against stress and vibration. TIME-SERT® is thin walled due to synchronized internal external threads. Thin cross sectional area allows for installation in areas of limited space and clearance material. TIME-SERT® Positive Placement. Having a flange on the top of the insert will insure that the insert will have positive placement and cannot wind down into the newly repaired hole. TIME-SERT® is self locking. On installation the bottom internal threads of the insert are cold rolled to expand the mating external threads into the base material locking the insert in place. Locking mechanism is at the bottom of insert Learn More

Was: $10.99 ea.

Now: $9.99 ea.
Engine Gaskets, Complete, For Porsche®, 1969 Part # P914177
Engine gasket sets from original equipment manufacturers such as Reinz and Ehlring. Learn More

Was: $289.99 Set

Now: $249.99 Set
Engine Case Through Bolt, For Porsche® 911® Engines 11 Per Car, 1965 -1988 Part # P910316
Genuine Porsche PartJust like the cylinder head studs, the case through bolts stretch and stress over time. NEVER use the old case through bolts when you re-assemble your 911 engine-now is the perfect time to replace the old case through bolts with new OEbolts from Automotion. Learn More

Was: $249.99 ea.

Now: $39.99 ea.
Timesert Inserts, Head Stud Insert 10mm, For Porsche® Part # P910071
24 Piece Set   TIME-SERT® is a solid bushing insert. This guarantees easy installation and allows for full load use of tapped hole, ensuring protection against stress and vibration. TIME-SERT® is thin walled due to synchronized internal external threads. Thin cross sectional area allows for installation in areas of limited space and clearance material. TIME-SERT® Positive Placement. Having a flange on the top of the insert will insure that the insert will have positive placement and cannot wind down into the newly repaired hole. TIME-SERT® is self locking. On installation the bottom internal threads of the insert are cold rolled to expand the mating external threads into the base material locking the insert in place. Locking mechanism is at the bottom of insert. TIME-SERT® thread repair system the ultimate way to repair threads in stripped or damaged holes.   Learn More

Was: $34.99 Kit

Now: $29.99 Kit
Pushrod Tube Seals, For Porsche®, 1970 -1971 Part # P904113
These tube seals are neccesary when removing the heads from your air cooled motor, or rebuilding the engine. Often, with age these break, are damaged, or rust which will cause oil leaks. A set of 8 replaces all of them. This part meets or exceeds OE spec Learn More

Was: $19.99 Set

Now: $12.99 Set
Engine Hardware, ° Cap Nut (13 Per Car), For Porsche®, 1965 -1988 Part # P910319
Genuine Porsche PartMake sure you have all the hardware you need when you are ready to assembly your Porsche. Note: The Lock Tabs are used to secure the oil pump (2 per car), and the intermediate shaft gear (6 per car). Learn More

Was: $179.99 ea.

Now: $9.99 ea.
Timesert Thread Repair Kits & Inserts, 8mm Timesert Tap Kit, For Porsche® Part # P910353
5 Insert Set   TIME-SERT® is a solid bushing insert. This guarantees easy installation and allows for full load use of tapped hole, ensuring protection against stress and vibration. TIME-SERT® is thin walled due to synchronized internal external threads. Thin cross sectional area allows for installation in areas of limited space and clearance material. TIME-SERT® Positive Placement. Having a flange on the top of the insert will insure that the insert will have positive placement and cannot wind down into the newly repaired hole. TIME-SERT® is self locking. On installation the bottom internal threads of the insert are cold rolled to expand the mating external threads into the base material locking the insert in place. Locking mechanism is at the bottom of insert Learn More
$64.99 ea.
Porsche Cylinder Head Washer, 911, 912, 914, 1965-1976 Part # 65-10697
Quality Restoration Part Early Original Small Style 24 Required Per Engine Fits 2.0-2.7L Engines For OE See Part Number P901534 Learn More
$1.29 ea.
Engine Hardware, © Washer, For Porsche®, 1965 -1972 Part # P910318
Genuine Porsche Part 24 Required Per Car Make sure you have all the hardware you need when you are ready to assembly your Porsche. Note: The Lock Tabs are used to secure the oil pump (2 per car), and the intermediate shaft gear (6 per car). Learn More
$6.99 ea.
Porsche 911/914 Cylinder Case Base Gasket, 1965-1973 Part # 65-10692
Replacement Base Gasket .50mm Thick Replaces Porsche Part Number 901.104.191.02 Learn More
$2.99 ea.
26 Item(s) Sort by: Show: per page Grid  |  List
4